0

Full Content is available to subscribers

Subscribe/Learn More  >

Flame Describing Functions of a Confined Premixed Swirled Combustor With Upstream and Downstream Forcing

[+] Author Affiliations
R. Gaudron, M. Gatti, C. Mirat, T. Schuller

Université Paris-Saclay, Gif-sur-Yvette, France

Paper No. GT2018-76381, pp. V04BT04A021; 13 pages
doi:10.1115/GT2018-76381
From:
  • ASME Turbo Expo 2018: Turbomachinery Technical Conference and Exposition
  • Volume 4B: Combustion, Fuels, and Emissions
  • Oslo, Norway, June 11–15, 2018
  • Conference Sponsors: International Gas Turbine Institute
  • ISBN: 978-0-7918-5106-7
  • Copyright © 2018 by ASME

abstract

The frequency response of a confined premixed swirled flame is explored experimentally through the use of describing functions that depend on both the forcing frequency and forcing level. In these experiments, the flame is forced by a loudspeaker connected to the bottom of the burner in the fresh gas region or by a set of loudspeakers connected to the combustion chamber exhaust tube in the burnt gas region. The experimental setup is equipped with a hot-wire probe and a microphone, both of which located in front of each other below the swirler. The forcing level is varied between |v′0|/v̄0 = 0.10 and 0.72 RMS where v̄0 and v′0 are respectively the mean and fluctuating velocity at the hot-wire probe. An additional microphone is placed on a water-cooled waveguide connected to the combustion chamber backplate. A photomultiplier equipped with an OH* filter is used to measure the heat release rate fluctuations. The describing functions between the photomultiplier signal and the different pressure and velocity reference signals are then analyzed in the case of upstream and downstream forcing. The describing function measured for a given reference signal is shown to vary depending on the type of forcing. The impedance of the injector at the hot-wire location is also measured using the hot-wire and microphone signals for both upstream and downstream forcing. For all describing functions investigated, it is found that their phase lags do not depend on the forcing level whereas their gains strongly depend on |v′0|/v̄0 for certain frequency ranges. It is furthermore shown that the Flame Describing Function measured with respect to the hot-wire signal can be retrieved from the specific impedance at the hot-wire location and the describing function determined with respect to the signal of the microphone located in front of the hot-wire. This relationship is not valid when the signal from the microphone located at the combustion chamber backplate is considered. It is then shown that a ID acoustic model allows to reproduce the describing function computed with respect to the microphone signal inside the injector from the microphone signal located at the combustion chamber backplate in the case of downstream forcing. This relation does not hold for upstream forcing because of the acoustic dissipation across the swirler which is much larger compared to downstream forcing for a given forcing level set at the hot-wire location. This study sheds light on the differences between upstream and downstream acoustic forcing when measuring describing functions. It is also shown that the upstream and downstream forcing techniques are equivalent only if the reference signal used to determine the flame describing function is the acoustic velocity in the fresh gases just before the flame.

Copyright © 2018 by ASME

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In