0

Full Content is available to subscribers

Subscribe/Learn More  >

PDF Evolution of Texture in the Fabrication of Magneto-Active Elastomers

[+] Author Affiliations
Manuel Aurelio Rodriguez, Paris von Lockette

Pennsylvania State University, University Park, PA

Paper No. SMASIS2017-3868, pp. V001T01A008; 13 pages
doi:10.1115/SMASIS2017-3868
From:
  • ASME 2017 Conference on Smart Materials, Adaptive Structures and Intelligent Systems
  • Volume 1: Development and Characterization of Multifunctional Materials; Mechanics and Behavior of Active Materials; Bioinspired Smart Materials and Systems; Energy Harvesting; Emerging Technologies
  • Snowbird, Utah, USA, September 18–20, 2017
  • Conference Sponsors: Aerospace Division
  • ISBN: 978-0-7918-5825-7
  • Copyright © 2017 by ASME

abstract

Magneto-Active elastomers (MAEs) and magneto-rheological elastomers (MREs) are smart materials that consist of hard and soft magnetic particles, respectively, embedded in a flexible matrix. Their actuation capabilities are dependent on the arrangement of particles achieved during the fabrication process. Previous works have shown varying degrees of particle alignment and / or agglomeration as a function of fabrication process variable, most notably volume fraction of the particulates, their magnetic material type (hard vs soft), and the strength of the external field applied during curing. In this work, we simulated the dynamics of magnetic particles suspended in a fluid matrix to predict the evolution of microstructures resulting from these varying process conditions. The simulations accounted for the magnetic interaction of all particles using standard dipole-dipole interaction potentials along with dipole-field potentials developed from the Zeeman Energy. Additionally, the field local to each particle, on which magnetization depends, was determined by the sum of the external fields generated by each member of the ensemble and their demagnetizing fields. Fluid drag forces and short range particle-particle repulsion (non-overlapping) were also considered. These interactions determined the body forces and torques acting on each particle that drove the system of equations of motions for the ensemble of particles. The simulation was carried out over a nearest neighbor periodic unit cell using an adaptive time stepping numerical integration scheme until an equilibrium structure was reached. Structural parameters, related to the magnetic energy, spatial distribution, spatial alignment, and orientation alignments of the particle distributions were defined to characterize the simulated structures. The effect of volume fraction and intensity of the external magnetic field on the achieved particle distributions were studied. At low external field strengths, the particles formed long entangled chains that had very low alignment with the applied field. The remnant magnetic potential energy of these configurations was also significantly low. As the field is increased the length of the chains reduced and the alignment increased. The corresponding change in magnetic potential energy of the system with an increase in the applied field was found to follow a power law fit that spanned a wide range of magnetic field strengths. At low volume fractions the particles aligned rapidly with the field and formed short chains. As the volume fraction of the samples increased the chains grew longer and closer to each other, and magnetic potential of the structure became lower. Results of the simulations suggest that it is possible to tailor the microstructure and thus affect remanent magnetization and magnetization anisotropy, by judicious control of process parameters. This ability could have implications for newly emerging additive manufacturing techniques utilizing suspensions of magnetic particulates.

Copyright © 2017 by ASME

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In