0

Full Content is available to subscribers

Subscribe/Learn More  >

Development of Process Induced Residual Stress During Flow Forming of Tubular 15-5 Martensitic Stainless Steel

[+] Author Affiliations
Saber Khayatzadeh, Shanmukha Rao Moturu, Salah Rahimi

Strathclyde University, Glasgow, UK

Joe F. Kelleher

ISIS Pulsed Neutron & Muon Source, Oxfordshire, UK

Paper No. PVP2017-65806, pp. V06AT06A016; 10 pages
doi:10.1115/PVP2017-65806
From:
  • ASME 2017 Pressure Vessels and Piping Conference
  • Volume 6A: Materials and Fabrication
  • Waikoloa, Hawaii, USA, July 16–20, 2017
  • Conference Sponsors: Pressure Vessels and Piping Division
  • ISBN: 978-0-7918-5799-1
  • Copyright © 2017 by ASME

abstract

Flow forming is a near net shape process for manufacturing of dimensionally accurate hollow components such as shaft in gas turbines, that is currently at its development stage for aerospace industry. The process has several advantages such as reducing material wastage, extremely fast manufacturing time, and eliminating extra manufacturing processes such as machining. Due to the nature of this complicated cold deformation process, significant magnitude of residual stress is introduced into the component. Understanding the magnitude and distribution of residual stress is essential to tailor the flow forming process to achieve parts within dimensional tolerances and desired mechanical properties. The present research is aiming to explore the generation and evolution of residual stress at various stages of flow forming process in a tubular component made from martensitic 15Cr-5Ni stainless steel, using different techniques of neutron scattering, x-ray diffraction (XRD) and hole-drilling based on electronic speckle pattern interferometry (ESPI).

Residual stress measurements were carried out in preformed and flow formed components at surface, near-surface and in the bulk of components using XRD, ESPI based hole-drilling and neutron diffraction techniques. These measurements were conducted at different levels of reduction in the thickness of the original part (i.e. after 20% and 40%), by applying identical forming parameters for all samples. The XRD results show significant change in hoop and axial residual stress levels with a reduction in the wall thickness. This is more pronounced for the axial component where the average stress switches from relatively high tensile (∼ 450MPa) in the original part to significant compressive stress (∼ −600MPa) in the formed part, after 20% of reduction. The bulk residual stress components measured in the middle of thickness of the parts, using neutron scattering, show a general increase in the magnitude of residual stress by higher level of deformation (i.e. reduction in the wall thickness). The measured bulk stress components through the thickness were tuned to tensile after reducing the wall thickness by 40%. The results of XRD and neutron diffraction stress measurements suggest that the residual stress along the length of the samples (i.e. axial direction) is consistent with ±800 MPa and ±400 MPa after 20% and 40% reduction by forming process, respectively.

The results of ESPI based hole-drilling show tensile hoop residual stress (≈600 MPa) and an abrupt fluctuation (i.e. tension-compressive-tension) in the axial residual stress near the surface of the part following flow forming. The stresses measured by ESPI based hole-drilling are complementary to the results of the XRD on surface and neutron diffraction in the bulk to reconstruct the residual stress profile form the surface through to the bulk.

Copyright © 2017 by ASME

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In