0

Full Content is available to subscribers

Subscribe/Learn More  >

Investigation of High Pressure Effect on Drilling Fluid Rheology

[+] Author Affiliations
Muzaffer Gorkem Gokdemir, Selcuk Erkekol

Turkish Petroleum, Ankara, Turkey

Huseyin Ali Dogan

GEOS Energy, Ankara, Turkey

Paper No. OMAE2017-61449, pp. V008T11A063; 10 pages
doi:10.1115/OMAE2017-61449
From:
  • ASME 2017 36th International Conference on Ocean, Offshore and Arctic Engineering
  • Volume 8: Polar and Arctic Sciences and Technology; Petroleum Technology
  • Trondheim, Norway, June 25–30, 2017
  • Conference Sponsors: Ocean, Offshore and Arctic Engineering Division
  • ISBN: 978-0-7918-5776-2
  • Copyright © 2017 by ASME

abstract

Drilling fluid is the mixture of base fluid and special chemicals. The system is designed to meet operational requirements. These complex fluids can carry drilled cuttings to surface, provide enough force or pressure to the formation and have adequate holding capacity in pump-off period to prevent particle precipitation. These necessities are controlled by fluid rheology. The art of flow or flow science, i.e. rheology, examines the deformation and flow behavior of the fluid. Ideal viscous flow through ideal elastic deformation is analyzed in this branch.

Increase in energy demand and depletion of shallow hydrocarbon reserves has driven the industry to explore deeper reservoirs. Thanks to the technical developments in the drilling industry, operations can go further, especially in offshore wells. Non-aqueous conventional drilling fluid systems (NAS), synthetic based mud (SBM) or oil based mud (OBM), are favorable due to lubricity effect, high inhibitive characteristic and temperature-rheological stability in deep formations. Despite the advantages of NAS over the water based systems (WBM), their flow characteristics vary with pressure due to compressibility. Mezger stated that “For most liquids, the viscosity values are increasing with increasing pressure since the amount of free volume within the internal structure is decreasing due to compression, therefore the molecules are more and more limited in their mobility. This increases the internal frictional forces and the flow resistance”1. By considering the primary well control requirements, drilling fluid equivalent pressure in both static and dynamic conditions can overbalance the fluid pressure in the rock pores and cannot exceed the inelastic strength of the medium in conventional, over-balanced operations. Mud playing pressure window shrinks as the depth is increased and is even not tolerable in ultra-deep offshore wells. Incompetent fluid formulation and hydraulic design led to detrimental and vital problems. In literature, limited research on high pressure fluid deformation behavior and rheological experimental data are found to understand the flow behavior and rheological changes in down hole conditions2. Generally rheological measurements are taken at the surface conditions and extrapolated to the down hole conditions that cause the perversity in real high pressure deformation behavior.

This study is conducted to examine the high pressure effect on NAS rheology and to compare the experimental results to the conventional WBM. High Pressure, High Temperature (HPHT) Anton Paar MCR-302 compact rheometer (1,000 bar–14,500 psi, 300°C capacity) is preferred rather than using HPHT viscometers due to exact frictionless air bearings in the laboratory experiments. Controlled shear rate (CSR) and rate sweep test methodologies are used in the rheological tests. Tests are performed from ambient surface conditions to 12,000 psi pressure at constant temperature. To get a better understanding of flow properties and to have a more accurate hydraulic design, rheological characterization is simulated under in-situ conditions. Test results are analyzed to understand the compressibility and pressure effects on rheological parameters in constitutive equation (yield stress, apparent viscosity, and flow behavior index) and deformation behavior.

Copyright © 2017 by ASME

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In