0

Full Content is available to subscribers

Subscribe/Learn More  >

Prediction of Diesel Combustion and Emission Characteristics in CI Engine Using Computational Fluid Dynamics Simulations

[+] Author Affiliations
Meshack Hawi, Ali K. Abdel-Rahman

Egypt-Japan University of Science and Technology, Alexandria, Egypt

Mahmoud Bady

Islamic University of Medina, Medina, KSA

Shinichi Ookawara

Tokyo Institute of Technology, Tokyo, Japan

Paper No. ES2017-3058, pp. V001T02A001; 11 pages
doi:10.1115/ES2017-3058
From:
  • ASME 2017 11th International Conference on Energy Sustainability collocated with the ASME 2017 Power Conference Joint With ICOPE-17, the ASME 2017 15th International Conference on Fuel Cell Science, Engineering and Technology, and the ASME 2017 Nuclear Forum
  • ASME 2017 11th International Conference on Energy Sustainability
  • Charlotte, North Carolina, USA, June 26–30, 2017
  • Conference Sponsors: Advanced Energy Systems Division, Solar Energy Division
  • ISBN: 978-0-7918-5759-5
  • Copyright © 2017 by ASME

abstract

Computational Fluid Dynamics (CFD) study of compression ignition (CI) engines provides invaluable insights into in-cylinder conditions and processes, which greatly expands on the very limited detail provided by engine output measurements, fuel consumption measurements, and engine-out measurements of exhaust emissions. CFD modeling and simulation has therefore become an attractive alternative for engine analysis in place of full experimental testbed study in recent years. In this research work, the performance of a single cylinder four stroke diesel engine was investigated. Commercial simulation software ANSYS Forte was used to study the combustion and emission characteristics of a diesel engine, in order to establish strategies for improvement of in-cylinder combustion and emission control. Normal heptane (n-heptane) was used as the surrogate fuel to represent diesel. Simulation results are compared against data from experimental testbed studies in terms of in-cylinder pressure profiles, heat release rate and exhaust emission of oxides of nitrogen (NOx), soot and unburned hydrocarbon (UHC) levels. The pressure trace from the simulations is found to be within a reasonable error limit of 10%. The combustion process is simulated with special focus on exhaust emissions of soot, NOx and unburned hydrocarbon. Graphical plots for mass fraction of soot, NOx and UHC are presented and discussed to elucidate the formation of these emissions. Graphics contours of temperature, NO mass fraction and oxygen concentration within the combustion chamber are also presented and discussed. The effects of injection timing on engine in-cylinder pressure, heat release rate and exhaust emissions are also studied by varying the injection timing and maintaining constant injection duration. Results are compared for the three different injection timings investigated, namely start of injection (SOI) 18° bTDC, 15° bTDC and 12° bTDC. Emissions of soot and NOx are found to decrease with retarded injection timing. However, the peak in-cylinder pressure is greatly reduced and hence the output power is low. Injection timing is found to have no significant effect on emissions of UHC. The optimum injection timing that gives high output power and relatively low emission is 15° bTDC.

Copyright © 2017 by ASME

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In