0

Full Content is available to subscribers

Subscribe/Learn More  >

Investigation of Preparation Processes and Corrosion Resistance of NiCrBSi Coatings Fabricated by Laser-High Frequency Induction Hybrid Cladding

[+] Author Affiliations
Shuhua Lu, Xiang Ling, Jinchun Zhang

Nanjing Tech University, Nanjing, China

Paper No. PVP2016-63109, pp. V06AT06A013; 6 pages
doi:10.1115/PVP2016-63109
From:
  • ASME 2016 Pressure Vessels and Piping Conference
  • Volume 6A: Materials and Fabrication
  • Vancouver, British Columbia, Canada, July 17–21, 2016
  • Conference Sponsors: Pressure Vessels and Piping Division
  • ISBN: 978-0-7918-5042-8
  • Copyright © 2016 by ASME

abstract

The surface of many key components used in petrochemical industry may be damaged by corrosion, wear and overheat during service. This damage can make a significant impact on the safe and reliable operation process of the device. Low alloy steel is widely used to manufacture pressure vessels and pipes because of the higher strength and good processing properties, but has poor corrosion resistance and wear resistance. Laser cladding is an advanced and effective surface modification technology. It can improve the surface properties of the matrix material at lower cost. But these claddings crack easily due to the high temperature gradient in the laser molten pool and physical properties differences between the cladding material and matrix. This problem has affected the development of laser cladding. Laser-high frequency induction hybrid cladding is a novel technology which combines laser beam heat source and induction power. It can decrease the cracks in the claddings effectively and has been received significant attentions in recent years.

Nickel base alloy powders have good corrosion resistance, wettability and high temperature lubricity. In this research, NiCrBSi composite claddings were fabricated on the surface of low alloy steel by the way of laser-high frequency induction hybrid cladding and coaxial powder feeding. The optimum cladding technology parameters to obtain the cladding layers that with good metallurgical combination, reasonable dilution rate and without cracks and defects were developed by optimizing the processing parameters such as laser power, powder feeding rate, laser scanning speed and induction heating temperature. The hardness distribution, microstructure, element distribution and phase of the cladding layers fabricated by the optimum parameters were systematically investigated by means of micro-hardness tester, optical microscopy (OM). Compared with the untreated material, experiment results show that the micro-hardness from substrate to NiCrBSi cladding layer exhibits step distribution, and the hardness of the NiCrBSi cladding layer is higher than that of the base metal. The microstructure showed good metallurgical bonding between NiCrBSi cladding and substrate had been achieved. In addition, directionally solidified microstructures were deposited. From the top to bottom of the cladding layer, the microstructures are, in order, equiaxed crystal, dendrite crystal, cellular crystal, columnar crystal and plane crystals. The corrosion resistance of the base metal and specimens manufactured by laser-high frequency induction hybrid cladding were evaluated in 3.5% NaCl solution by electrochemical testing. The experimental results demonstrate that the corrosion resistance of the NiCrBSi cladding layer fabricated by laser-high frequency induction hybrid cladding technology is better than the base metal.

Copyright © 2016 by ASME

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In