0

Full Content is available to subscribers

Subscribe/Learn More  >

The Effect of Grid Resolution on Predicted Spray Variability Using Multiple Large-Eddy Spray Simulations

[+] Author Affiliations
Noah Van Dam, Sibendu Som, Andrew B. Swantek, Christopher F. Powell

Argonne National Laboratory, Lemont, IL

Paper No. ICEF2016-9384, pp. V001T06A013; 11 pages
doi:10.1115/ICEF2016-9384
From:
  • ASME 2016 Internal Combustion Engine Division Fall Technical Conference
  • ASME 2016 Internal Combustion Engine Division Fall Technical Conference
  • Greenville, South Carolina, USA, October 9–12, 2016
  • Conference Sponsors: Internal Combustion Engine Division
  • ISBN: 978-0-7918-5050-3
  • Copyright © 2016 by ASME

abstract

Shot-to-shot spray variability is recognized as an important contributor to cycle-to-cycle variations in direct-injection engines. Large-eddy Simulations (LES) have been used to resolve more of the gas-phase turbulent fluctuations in Computational Fluid Dynamics (CFD) simulations, but the sources of shot-to-shot spray variability are not directly modeled in the Lagrangian parcel approach used most often for engine fuel spray simulations. Instead, the variability comes from variations in the spray boundary conditions. Currently, the most common way to introduce shot-to-shot variability in Lagrangian spray simulations is to vary the random seed used in the spray models for each spray realization. This approach was used to compare against recent near-nozzle (up to ≈9 mm downstream) projected mass density (PMD) measurements of a single-hole diesel injector. The injector has a nominal nozzle diameter of 110 μm, though analysis of experimental data indicates the actual diameter is approximately 118 μm. The measurements were acquired under non-vaporizing conditions using fast radiography with high-intensity X-rays available at the Advanced Photon Source at Argonne National Laboratory.

Spray simulations used the Dynamic Structure LES turbulence model along with a Lagrangian parcel approach with the blob injection model and modified KH-RT break-up model. 10 spray realizations were simulated each at three different minimum cell sizes, 62.5 μm, 93.75 μm and 125 μm. This is much finer mesh resolution than is typically performed for Lagrangian spray calculations and allows the simulations to capture more of the gas-phase turbulent fluctuations that develop from the different random seeds. The effect of the grid resolution on the predicted shot-to-shot variability was investigated. Larger minimum cell sizes increased the predicted variability in projected mass density slightly. This difference in predicted variability was less apparent in global spray quantities such as penetration length.

Initial turbulence kinetic energy (TKE) variations have also been proposed as a method to introduce shot-to-shot variations in spray simulations. 10 further simulations were run where the initial turbulence intensity was varied randomly between 0.1 and 1 m2/s2. The resulting spray variability was similar, but slightly lower than that introduced by varying the random seed.

Copyright © 2016 by ASME

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In