0

Full Content is available to subscribers

Subscribe/Learn More  >

Freeform Extrusion Fabrication of Advanced Ceramic Components With Embedded Sapphire Optical Fiber Sensors

[+] Author Affiliations
Amir Ghazanfari, Wenbin Li, Ming C. Leu, Jeremy Watts, Yiyang Zhuang, Jie Huang

Missouri University of Science and Technology, Rolla, MO

Paper No. SMASIS2016-9270, pp. V001T04A014; 11 pages
doi:10.1115/SMASIS2016-9270
From:
  • ASME 2016 Conference on Smart Materials, Adaptive Structures and Intelligent Systems
  • Volume 1: Multifunctional Materials; Mechanics and Behavior of Active Materials; Integrated System Design and Implementation; Structural Health Monitoring
  • Stowe, Vermont, USA, September 28–30, 2016
  • Conference Sponsors: Aerospace Division
  • ISBN: 978-0-7918-5048-0
  • Copyright © 2016 by ASME

abstract

Traditionally, sensors to be integrated into a structural component are attached to or mounted on the component after the component has been fabricated. This tends to result in unsecured sensor attachment and/or serious offset between the sensor reading and the actual status of the structure, leading to performance degradation of the host structure. This paper describes a novel extrusion-based additive manufacturing process that has been developed to enable embedment of sensors in ceramic components during the part fabrication. In this process, an aqueous paste of ceramic particles with a very low amount of binder content (< 1 vol%) is extruded through a moving nozzle to build the part layer-by-layer. In the case of sensor embedment, the fabrication process is halted after a certain number of layers have been deposited. The sensors are placed in their predetermined locations, and the remaining layers are deposited until the part fabrication is completed. Because the sensors are embedded during the fabrication process, they are fully integrated with the part and the aforementioned problems of traditional sensor embedment can be eliminated. The sensors used in this study were made of sapphire optical fibers of 125 and 250 micro-meters diameter and can withstand temperatures up to 1600 °C. After the parts were built, two different drying processes (freeze drying and humid drying) were investigated to dry the parts. The dried parts were then sintered to achieve near theoretical density. Scanning electron microscopy was used to observe the embedded sensors and to detect any possible flaws in the part or embedded sensor. Attenuation of the sensors was measured in near-infrared region (1500–1600 nm wavelength) with a tunable laser source. Raman spectroscopy was performed on the samples to measure the residual stresses caused by shrinkage of the part and its slippage on the fibers during sintering and mismatch between the coefficients of thermal expansion of the fiber and host material. Standard test methods were employed to examine the effect of embedded fibers on the strength and hardness of the parts. The result indicated that the sapphire fiber sensors with diameters smaller than 250 micrometers are able to endure the freeform extrusion fabrication process and also the post-processing without compromising the part properties.

Copyright © 2016 by ASME

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In