0

NOx-Abatement Potential of Lean-Premixed GT-Combustors FREE

[+] Author Affiliations
T. Sattelmayer, W. Polifke, D. Winkler, K. Döbbeling

ABB Corporate Research, Baden-Dättwil, Switzerland

Paper No. 96-TA-021, pp. V001T02A003; 14 pages
doi:10.1115/96-TA-021
From:
  • ASME 1996 Turbo Asia Conference
  • ASME 1996 Turbo Asia Conference
  • Jakarta, Indonesia, November 5–7, 1996
  • Conference Sponsors: International Gas Turbine Institute
  • ISBN: 978-0-7918-7877-4
  • Copyright © 1996 by ASME

abstract

The influence of the structure of perfectly premixed flames on NOx-formation is investigated theoretically. Since a network of reaction kinetics modules and model flames is used for this purpose, the results obtained are independent of specific burner geometries. Calculations are presented for a mixture temperature of 630K, an adiabatic flame temperature of 1840K and 1 and 15 bars combustor pressure. In particular, the following effects are studied separately from each other:

- molecular diffusion of temperature and species

- flame strain

- local quench in highly strained flames and subsequent reignition

- turbulent diffusion (no preferential diffusion)

- small scale mixing (stirring) in the flame front

Either no relevant influence or an increase in NOx-production over that of the one-dimensional laminar flame is found. As a consequence, besides the improvement of mixing quality, a future target for the development of low-NOx burners is to avoid excessive turbulent stirring in the flame front. Turbulent flames that exhibit locally and instantaneously near laminar structures (“flamelets”) appear to be optimal.

Using the same methodology, the scope of the investigation is extended to lean-lean staging, since a higher NOx-abatement potential can be expected in principle. As long as the chemical reactions of the second stage take place in the boundary between the fresh mixture of the second stage and the combustion products from upstream, no advantage can be expected from lean-lean staging. Only if the primary burner exhibits much poorer mixing than the second stage can lean-lean staging be beneficial. In contrast, if full mixing between the two stages prior to afterburning can be achieved (lean-mix-lean technique), the combustor outlet temperature can in principle be increased somewhat without NO-penalty. However, the complexity of such a system with a larger flame tube area to be cooled will increase the reaction zone temperatures, so that the full advantage cannot be realised in an engine.

Of greater technical relevance is the potential of a lean-mix-lean combustion system within an improved thermodynamic cycle. A reheat process with sequential combustion is perfectly suited for this purpose, since, firstly, the required low inlet temperature of the second stage is automatically generated after partial expansion in the high pressure turbine, secondly, the efficiency of the thermodynamic cycle has its maximum and, thirdly, high exhaust temperatures are generated, which can drive a powerful Rankine cycle. The higher thermodynamic efficiency of this technique leads to an additional drop in NOx-emissions per power produced.

Copyright © 1996 by ASME
This article is only available in the PDF format.

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In