0

Numerical Prediction of the Dynamic Behaviour of Premixed Flames Using Systematically Reduced Multi-Step Reaction Mechanisms FREE

[+] Author Affiliations
Dieter Bohn, Yuhong Li, Gero Matouschek

Aachen University of Technology, Germany

Uwe Krüger

B&B-AGEMA, Aachen, Germany

Paper No. 97-GT-265, pp. V002T06A034; 12 pages
doi:10.1115/97-GT-265
From:
  • ASME 1997 International Gas Turbine and Aeroengine Congress and Exhibition
  • Volume 2: Coal, Biomass and Alternative Fuels; Combustion and Fuels; Oil and Gas Applications; Cycle Innovations
  • Orlando, Florida, USA, June 2–5, 1997
  • Conference Sponsors: International Gas Turbine Institute
  • ISBN: 978-0-7918-7869-9
  • Copyright © 1997 by ASME

abstract

Environmental compatibility requires low emission burners for both gas turbine power plants and jet engines. In the past, significant progress has been made in the development of low NOx and CO burners by introducing lean premixed techniques. Unfortunately these burners often have a more pronounced tendency than conventional burner designs to produce combustion driven oscillations. The oscillations may be excited to such an extent that strong pulsation may occur, and this is associated with a risk of engine failure.

In order to describe the acoustical behaviour of the complete burner system, it is crucial to determine the unit function response of the flame itself. Using a new method which was presented in 1996 by Bohn et al. [1] the dynamic flame behaviour can be predicted by means of a full Navier-Stokes-simulation of the complex combustion process for both the steady-state and transient case.

The authors have successfully used this method to obtain the frequency response of turbulent diffusion flames which are mainly controlled by the mixing process. Chemical kinetics become dominant for premixed flames. Therefore, the combustion process of a premixed methane-air mixture is modelled using a systematically reduced 6-step reaction mechanism which takes account of a set of 25 elementary reactions. This reduced mechanism was implemented in the 3D-Navier-Stokes solver in order to perform a combined flow and combustion computation.

The dynamic combustion process of a laminar premixed methane flame in a matrix burner configuration has been investigated. At first, the steady-state combustion process was simulated using the code described above. The results are compared with experimental data. Very good agreement over a wide range of equivalence ratios has been found for quantities such as laminar burning velocity or adiabatic flame temperature. The steady state results are then used as an operating point from which the transient flame behaviour after a sudden jump in the mass flow at the burner inlet has been obtained. Finally, these data lead to the unit function response which can be transferred into frequency space by a Laplace transformation.

The frequency response of the premixed methane flame obtained by a Navier-Stokes simulation has been compared with both experimental as well as analytical solutions. It must be stressed that a pure delay time element which is often used as an analytical formulation is not suitable to describe the dynamic flame behaviour in detail. The frequency response shows the characteristics of a higher order delay time element with several important details.

Parametric studies on the influence of equivalence ratio and the flow pattern of the internal burner fluid flow which are of interest for gas turbine applications, show the importance of the detailed knowledge of the dynamic flame behaviour for the stability analysis of a gas turbine combustor.

Copyright © 1997 by ASME
Topics: Flames
This article is only available in the PDF format.

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In