Full Content is available to subscribers

Subscribe/Learn More  >

Numerical Simulation of Air Sampling in Micro Scale Rising Bubbles

[+] Author Affiliations
Iman Mirzaee Kakhki, Majid Charmchi, Hongwei Sun, Minghao Song

University of Massachusetts Lowell, Lowell, MA

Paper No. HT2013-17510, pp. V003T09A008; 10 pages
  • ASME 2013 Heat Transfer Summer Conference collocated with the ASME 2013 7th International Conference on Energy Sustainability and the ASME 2013 11th International Conference on Fuel Cell Science, Engineering and Technology
  • Volume 3: Gas Turbine Heat Transfer; Transport Phenomena in Materials Processing and Manufacturing; Heat Transfer in Electronic Equipment; Symposium in Honor of Professor Richard Goldstein; Symposium in Honor of Prof. Spalding; Symposium in Honor of Prof. Arthur E. Bergles
  • Minneapolis, Minnesota, USA, July 14–19, 2013
  • Conference Sponsors: Heat Transfer Division
  • ISBN: 978-0-7918-5549-2
  • Copyright © 2013 by ASME


Capturing particles, mainly bio-particles, such as viruses and spores, from the air into a liquid is critical for air purification and analysis of the sampling systems. In the conventional impinger sampling systems, the air bubbles carrying the particles are injected into a liquid column. The particles are captured from the air into the liquid as the bubbles travel to the surface due to the buoyancy forces. This paper focuses on the numerical simulation of a newly developed microfluidic air sampling system. In this system, a microscale liquid column, equipped with an array of microchannels as pressure controlled gas injection points, is used for gas bubbling process for air sampling purpose. The air bubbles containing the particles are injected into the bottom of the microscale column filled with a liquid (such as water). As the microscale bubbles (of about 250∼500 microns) travel to the surface, a shear driven flow will develop within the bubbles and the airborne particles will follow the flow toward the boundary of the bubble. The inertia force of particles will result in the departure of particles from the flow into the liquid. The fraction of the particles departed from air bubble and trapped in the liquid represents the collection efficiency of the air sampler. For tracking the liquid/gas interface, the Volume-of-Fluid (VOF) method along with Youngs’ algorithm for geometric reconstruction of the free surface is used. The particle trajectories are predicted by integrating the force balance on each particle, which is based on a Lagrangian frame of reference. It is found that in addition to the particle departure during the bubble rising, a considerable amount of particles are trapped in the liquid during the air injection and bubble formation which may be due to the high velocity of the injected air and oscillation of the bubble interface. It is worth noting that this is the first time that the numerical simulation is performed to understand the whole air sampling process which was never addressed in the past. As a comparison, an experimental study was conducted to measure the collection efficiency. The fluorescent polystyrene latex particles with different diameters (diameters: 0.5, 1, 2 microns) were used in the experiment. The experimental results were compared with that of numerical simulation. Both the experiments and computations revealed that a collection efficiency of 90% can be achieved by the microfluidics based impinger, which is much higher than that of conventional, macro-scale, impinger systems. In addition to verifying the existing experimental work, this numerical simulation method provides a valuable tool to design and improve new generations of air sampling systems.

Copyright © 2013 by ASME



Interactive Graphics


Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In