0

Full Content is available to subscribers

Subscribe/Learn More  >

Ruptures in Gas Pipelines, Liquid Pipelines and Dense Phase Carbon Dioxide Pipelines

[+] Author Affiliations
Andrew Cosham

Atkins, Newcastle upon Tyne, UK

David G. Jones

Pipeline Integrity Engineers, Newcastle upon Tyne, UK

Keith Armstrong, Daniel Allason

GL Noble Denton, Spadeadam Test Site, UK

Julian Barnett

National Grid, Warwick, UK

Paper No. IPC2012-90463, pp. 465-482; 18 pages
doi:10.1115/IPC2012-90463
From:
  • 2012 9th International Pipeline Conference
  • Volume 3: Materials and Joining
  • Calgary, Alberta, Canada, September 24–28, 2012
  • Conference Sponsors: International Petroleum Technology Institute, Pipeline Division
  • ISBN: 978-0-7918-4514-1
  • Copyright © 2012 by ASME

abstract

Ruptures in gas and liquid pipelines are different. A rupture in a gas pipeline is typically long and wide. A rupture in a liquid pipeline is typically short and narrow, i.e. a slit or ‘fish-mouth’ opening.

The decompression of liquid (or dense) phase carbon dioxide (CO2) immediately after a rupture is characterised by a rapid decompression through the liquid phase, and then a long plateau. At the same initial conditions (pressure and temperature), the initial speed of sound in dense phase CO2 is greater than that of natural gas and less than half that of water. Consequently, the initial decompression is more rapid than that of natural gas, but less rapid than that of water.

A question then arises … Does a rupture in a liquid (or dense) phase CO2 pipeline behave like a rupture in a liquid pipeline or a gas pipeline? It may exhibit behaviour somewhere in-between the two. A ‘short’ defect that would rupture at the initial pressure might result in a short, narrow rupture (as in a liquid pipeline). A ‘long’ defect that would rupture at the (lower) saturation pressure might result in a long, wide rupture (as in a gas pipeline). This is important, because a rupture must be long and wide if it is to have the potential to transform into a running fracture.

Three full-scale fracture propagation tests (albeit shorter tests than a typical full-scale test) published in the 1980s demonstrate that it is possible to initiate a running ductile fracture in a CO2 pipeline. However, these tests were on relatively small diameter, thin-wall line pipe with a (relatively) low toughness. The results are not applicable to large diameter, thick-wall line pipe with a high toughness.

Therefore, in advance of its full-scale fracture propagation test using a dense phase CO2-rich mixture and 914×25.4 mm, Grade L450 line pipe, National Grid has conducted three ‘West Jefferson Tests’. The tests were designed to investigate if it was indeed possible to create a long, wide rupture in modern, high toughness line pipe steels using a dense phase CO2-rich mixture. Two tests were conducted with 100 mol.% CO2, and one with a CO2-rich binary mixture.

Two of the ‘West Jefferson Tests’ resulted in short ruptures, similar to ruptures in liquid pipelines. One test resulted in a long, wide rupture, similar to a rupture in a gas pipeline. The three tests and the results are described. The reasons for the different behaviour observed in each test are explained. It is concluded that a long, wide rupture can be created in large diameter, thick-wall line pipe with a high toughness if the saturation pressure is high enough and the initial defect is long.

Copyright © 2012 by ASME

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In