0

Full Content is available to subscribers

Subscribe/Learn More  >

Investigating the Use of Heavy Alcohols as a Fuel Blending Agent for Compression Ignition Engine Applications

[+] Author Affiliations
Anita I. Ramírez

University of Illinois at Chicago, Chicago, IL

Sibendu Som, Lisa A. LaRocco, Timothy P. Rutter, Douglas E. Longman

Argonne National Laboratory, Argonne, IL

Paper No. ICES2012-81169, pp. 151-161; 11 pages
doi:10.1115/ICES2012-81169
From:
  • ASME 2012 Internal Combustion Engine Division Spring Technical Conference
  • ASME 2012 Internal Combustion Engine Division Spring Technical Conference
  • Torino, Piemonte, Italy, May 6–9, 2012
  • Conference Sponsors: Internal Combustion Engine Division
  • ISBN: 978-0-7918-4466-3
  • Copyright © 2012 by ASME

abstract

There has been an extensive worldwide search for alternate fuels that fit with the existing infrastructure and would thus displace fossil-based resources. In metabolic engineering work at Argonne National Laboratory, strains of fuel have been designed that can be produced in large quantities by photosynthetic bacteria, eventually producing a heavy alcohol called phytol (C20H40O). Phytol’s physical and chemical properties (cetane number, heat of combustion, heat of vaporization, density, surface tension, vapor pressure, etc.) correspond in magnitude to those of diesel fuel, suggesting that phytol might be a good blending agent in compression ignition (CI) engine applications. The main reason for this study was to investigate the feasibility of using phytol as a blending agent with diesel; this was done by comparing the performance and emission characteristics of different blends of phytol (5%, 10%, 20% by volume) with diesel. The experimental research was performed on a single-cylinder engine under conventional operating conditions. Since phytol’s viscosity is much higher than that of diesel, higher-injection-pressure cases were investigated to ensure the delivery of fuel into the combustion chamber was sufficient. The influence of the fuel’s chemical composition on performance and emission characteristics was captured by doing an injection timing sweep. Combustion characteristics as shown in the cylinder pressure trace were comparable for the diesel and all the blends of phytol at each of the injection timings. The 5% and 10% blends show lower CO and similar NOx values. However, the 20% blend shows higher NOx and CO emissions, indicating that the chemical and physical properties have been altered substantially at this higher percentage. The combustion event was depicted by performing high-speed natural luminosity imaging using endoscopy. This revealed that the higher in-cylinder temperatures for the 20% blend are the cause for its higher NOx emissions. In addition, three-dimensional simulations of transient, turbulent nozzle flow were performed to compare the injection and cavitation characteristics of phytol and its blends. Specifically, area and discharge coefficients and mass flow rates of diesel and phytol blends were compared under corresponding engine operating conditions. The conclusion is that phytol may be a suitable blending agent with diesel fuel for CI applications.

Copyright © 2012 by ASME
Topics: Fuels , Diesel engines

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In