0

Full Content is available to subscribers

Subscribe/Learn More  >

Examination of Dust in AVR Pipe Components

[+] Author Affiliations
Johannes Fachinger, Heiko Barnert, Alexander P. Kummer, Guido Caspary, Manuel Seubert

Forschungszentrum Jülich, Jülich, North Rhine-Westphalia, Germany

Albert Koster, Munyaradzi Makumbe, Lolan Naicker

Pebble Bed Modular Reactor (Pty.) Ltd., Centurion, Gauteng, South Africa

Paper No. HTR2008-58033, pp. 591-602; 12 pages
doi:10.1115/HTR2008-58033
From:
  • Fourth International Topical Meeting on High Temperature Reactor Technology
  • Fourth International Topical Meeting on High Temperature Reactor Technology, Volume 1
  • Washington, DC, USA, September 28–October 1, 2008
  • Conference Sponsors: ASME
  • ISBN: 978-0-7918-4854-8 | eISBN: 978-0-7918-3834-1
  • Copyright © 2008 by ASME

abstract

Pebble Bed HTGR’s like the AVR in Jülich have the advantage of continuous fuelling. However the multiple passes of the fuel pebbles through the core have the disadvantage that the pebble’s movement through the fuelling system and the core produces graphite dust. This dust is transported from the core to other parts of the primary circuit and deposits on components. Although previous experiments performed during AVR operation have given some insight into the dust particle size and activity, there is little information on the behaviour of the dust that was deposited in the system. The decommissioning of the AVR has provided the opportunity to sample and characterise such dust from a number of components and gauge the adhesion strength. From the side of PBMR Pty Ltd this opportunity is considered important to enhance the knowledge about dust characteristics before the PBMR Demonstration Power Plant (DPP) is operational and able to produce specific plant information through sampling and analysis. AVR GmbH has provided a number of pipes and joints for investigation of loose and bound dust. Phase 1 of the analysis was used to determine the best techniques to be used on larger items. No measurable loose dust could be collected. Thereupon rings were cut from a T-section and subdivided into eight segments. The surface of the untreated segments were photographed and documented by optical microscopy, the dose rates were measured and gamma-spectrometry performed. Following this a mechanical or chemical decontamination was carried out to remove and isolate the bound dust. The average isolated dust amount was about 2 mg/cm2 . Both decontamination processes indicates a strong bonding of the dust surface layer. In the case of mechanical decontamination about 60% and by chemical decontamination about 95% of the radionuclide inventory could be removed. The contribution of removed metal needs to be investigated in more detail. The median number related particle size measured by optical microscopy was found to be in the range of 0.2 to 0.7 μm whereas the median weight related size is in the range of 0.8 to 1.5 μm. The initial results indicate that this dust sticks very strongly to the pipe surface. Phase 2 will concentrate on longer pieces of piping where hopefully more loose dust can be obtained and analysed. If the same strong bonding is observed the reason for this phenomenon needs to be explained and perhaps tested with non-active dust.

Copyright © 2008 by ASME
Topics: Dust , Pipes

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In