0

Full Content is available to subscribers

Subscribe/Learn More  >

Fabrication Process and Product Quality Improvements in Advanced Gas Reactor UCO Kernels

[+] Author Affiliations
Charles M. Barnes, Matthias Ebner

Idaho National Laboratory, Idaho Falls, ID

W. C. Richardson, DeWayne Husser

Babcock & Wilcox, Lynchburg, VA

Paper No. HTR2008-58039, pp. 177-188; 12 pages
doi:10.1115/HTR2008-58039
From:
  • Fourth International Topical Meeting on High Temperature Reactor Technology
  • Fourth International Topical Meeting on High Temperature Reactor Technology, Volume 1
  • Washington, DC, USA, September 28–October 1, 2008
  • Conference Sponsors: ASME
  • ISBN: 978-0-7918-4854-8 | eISBN: 978-0-7918-3834-1
  • Copyright © 2008 by ASME

abstract

A major element of the Next Generation Nuclear Plant (NGNP)/Advanced Gas Reactor (AGR) Fuel Development and Qualification Program is developing fuel fabrication processes to produce high quality uranium-containing fuel kernels, TRISO-coated particles and fuel compacts needed for planned irradiation tests. The goals of the program also include developing the fabrication technology to mass produce this fuel at low cost. Kernels for the first AGR test, AGR-1, consisted of uranium oxycarbide (UCO) microspheres that were produced by an internal gelation process followed by high temperature steps to convert the UO3 + C “green” microspheres to UO2 + UCx . The high temperature steps also densified the kernels. Babcock and Wilcox (B&W) fabricated UCO kernels in their Lynchburg facility for the AGR-1 irradiation experiment, which went into the Advanced Test Reactor (ATR) at Idaho National Laboratory in December 2006. An evaluation of the kernel process prior and after these kernels were produced led to several recommendations to improve the fabrication process. These recommendations included testing alternative methods of dispersing carbon during broth preparation, evaluating the method of broth mixing, optimizing the broth chemistry, optimizing sintering conditions, and demonstrating fabrication of larger diameter UCO kernels needed for the second AGR irradiation test, AGR-2. Based on these recommendations and requirements, a test program was defined and performed. Certain portions of the test program were performed by Oak Ridge National Laboratory (ORNL), while tests at larger scale were performed by B&W. The tests at B&W have demonstrated improvements in both kernel properties and process operation. Changes in the form of carbon black used and the method of mixing the carbon prior to forming kernels led to improvements in the phase distribution in the sintered kernels, greater consistency in kernel properties, a reduction in forming run time, and simplifications to the forming process. Process parameter variation tests in both forming and sintering steps led to an increased understanding of the acceptable ranges for process parameters and additional reduction in required operating times. Another result of this test program was to double the kernel production rate. Following the development tests, approximately 40 kg of natural uranium UCO kernels have been produced for use in coater scale up tests, and approximately 10 kg of low enriched uranium UCO kernels for use in the AGR-2 experiment.

Copyright © 2008 by ASME

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In