0

Full Content is available to subscribers

Subscribe/Learn More  >

Characterization of Die Stress Distributions in Area Array Flip Chip Packaging

[+] Author Affiliations
Jordan Roberts, M. Kaysar Rahim, Jeffrey C. Suhling, Richard C. Jaeger, Pradeep Lall

Auburn University, Auburn, AL

Ron Zhang

Sun Microsystems, Sunnyvale, CA

Paper No. InterPACK2009-89383, pp. 977-988; 12 pages
doi:10.1115/InterPACK2009-89383
From:
  • ASME 2009 InterPACK Conference collocated with the ASME 2009 Summer Heat Transfer Conference and the ASME 2009 3rd International Conference on Energy Sustainability
  • ASME 2009 InterPACK Conference, Volume 1
  • San Francisco, California, USA, July 19–23, 2009
  • Conference Sponsors: Electronic and Photonic Packaging Division
  • ISBN: 978-0-7918-4359-8 | eISBN: 978-0-7918-3851-8
  • Copyright © 2009 by ASME

abstract

On-chip piezoresistive stress sensors represent a unique approach for characterizing stresses in silicon die embedded within complicated packaging architectures. In this work, we have used test chips containing such sensors to measure the stresses induced in microprocessor die after various steps of the assembly process, as well as to continuously characterize the in-situ die surface stress during thermal cycling and power cycling. The utilized (111) silicon sensor rosettes were able to measure the complete three-dimensional stress state (all 6 stress components) at each sensor site being monitored by the data acquisition hardware. The test chips had dimensions of 20 × 20 mm, and 3600 lead free solder interconnects (full area array) were used to connect the chips to high CTE ceramic chip carriers. Before packaging, the sensor resistances were measured by directly probing the test chip wafers. The chips were then diced, reflowed to the ceramic substrate, and then underfilled and cured. Finally, a metallic lid was attached to complete the ceramic LGA package. After every packaging step (solder reflow, underfill dispense and cure, lid attachment and adhesive cure), the sensor resistances were re-measured, so that the die stresses induced by each assembly operation could be characterized. The build-up of the die stresses was found to be monotonically increasing, and the relative severity of each assembly step was judged and compared. Such an approach also allows for various material sets (solders, underfills, TIM materials, lid metals, and lid adhesives) to be analyzed and rated for their contribution to the die stress level. After first level packaging of the chips on the ceramic chip carriers, initial experiments have been performed to analyze the effects of thermal cycling and power cycling on the die stresses. Thermal cycling of selected parts was performed from 0 to 100 C (40 minute cycle, 10 minute ramps and dwells). Power cycling of selected parts was performed by exciting the on-chip heaters on the test chips with power levels typical of microprocessor die. During the thermal/power cycling, sensor resistances at critical locations on the die device surface (e.g. die center and die corners) were recorded continuously. From the resistance data, the stresses at each site were calculated and plotted versus time. The experimental observations show some cycle-to-cycle evolution in the stress magnitudes due to material aging effects, stress relaxation and creep phenomena, and development of interfacial damage. The observed stress variations as a function of temperature cycling duration are currently being correlated with the delaminations occurring at the interfaces between the die and underfill and the die and lid adhesive. In addition, finite element models of the packages are being developed and correlated with the data.

Copyright © 2009 by ASME
Topics: Stress , Packaging , Flip-chip

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In