0

Full Content is available to subscribers

Subscribe/Learn More  >

A CFR1065-Compliant Transportable/On-Road Low Emissions Measurement Laboratory With Dual Primary Full-Flow Dilution Tunnels

[+] Author Affiliations
Yuebin Wu, Daniel Carder, Benjamin Shade, Richard Atkinson, Nigel Clark, Mridul Gautam

West Virginia University, Westover, WV

Paper No. ICES2009-76090, pp. 399-410; 12 pages
doi:10.1115/ICES2009-76090
From:
  • ASME 2009 Internal Combustion Engine Division Spring Technical Conference
  • ASME 2009 Internal Combustion Engine Division Spring Technical Conference
  • Milwaukee, Wisconsin, USA, May 3–6, 2009
  • Conference Sponsors: Internal Combustion Engine Division
  • ISBN: 978-0-7918-4340-6 | eISBN: 978-0-7918-3843-3
  • Copyright © 2009 by ASME

abstract

In 2007, certification standards for heavy duty diesel particulate matter (PM) emissions were reduced from 0.1g/bhp-hr to 0.01g/bhp-hr, representing an order of magnitude reduction in pollutant level. Coincident with these standards revisions are refinements to test procedures that target reductions in measurement uncertainties. The 2007 U.S. Environmental Protection Agency (US EPA) specifications, as defined in 40 CFR parts 86, and US EPA 2010 specifications, as defined in CFR 1065, require significant updates to established laboratory measurement systems and test procedures. Moreover, additional regulatory standards pertaining to in-use compliance of heavy duty diesel engines will significantly impact the future of heavy duty diesel emissions measurement. As a result of the reduced emission production levels, demand for ‘real-world’ emissions measurements, and subsequent development and evaluation of on-board emissions measurement systems, West Virginia University’s Center for Alternative Fuels, Engines, and Emissions (CAFEE) has designed and constructed, with support from the U.S. Department of Energy (DOE), the ‘next level’ transportable dual primary full-flow dilution tunnel emissions measurement laboratory. The objective of this project was to build a mobile emissions measurement laboratory, of engine test cell quality, that is capable of measuring regulated and non-regulated emissions, and meets US EPA 2007 and 2010 specifications. A thirty-foot long cargo container was constructed to house a portable emissions measurement facility, comprised of a High Efficiency Particulate Air (HEPA) primary dilution unit, two primary full-flow dilution tunnels, a subsonic venturi, a secondary particulate matter sampling system, a gaseous emissions analytical bench instrumentation system, a computer based data acquisition (DAQ) and control system, full air conditioning and ventilation system, and chassis dynamometer control systems. Dual tunnels, of 18 inches ID and 20 feet long provide dedicated measurement capability for both lower PM vehicles, as well as legacy diesel fueled vehicles. This provision reduces tunnel history effects between test programs which address differing exhaust composition and PM loading. The laboratory grade analytical system can be transported to virtually any location with a demand for emissions testing, either with or without WVU’s transportable medium or heavy duty chassis dynamometers. Alternatively, the system can be loaded onto a flatbed trailer in order to test emissions while a vehicle is operated over the road. This paper describes each sub-system of this transportable laboratory in the aspect of specifications and design considerations, and presents results of qualification tests on the laboratory.

Copyright © 2009 by ASME

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In