Full Content is available to subscribers

Subscribe/Learn More  >

A National Perspective: Establishing and Implementing a Characterization Program in the U.S. for Remote-Handled Transuranic Waste

[+] Author Affiliations
Roger Nelson, Alton D. Harris, III

U.S. Department of Energy, Washington, D.C.

Paper No. ICEM2007-7129, pp. 1055-1058; 4 pages
  • The 11th International Conference on Environmental Remediation and Radioactive Waste Management
  • 11th International Conference on Environmental Remediation and Radioactive Waste Management, Parts A and B
  • Bruges, Belgium, September 2–6, 2007
  • Conference Sponsors: Nuclear Division and Environmental Engineering Division
  • ISBN: 978-0-7918-4339-0 | eISBN: 0-7918-3818-8
  • Copyright © 2007 by ASME


The U.S. Department of Energy (DOE) is responsible for waste management from nuclear weapons production and operates the Waste Isolation Pilot Plant (WIPP) for permanent disposal of defense-generated transuranic waste (TRU), as authorized by Congress in 1979. Radioactive waste in the U.S. has historically been managed in one of two ways depending on its penetrating radiation dose rate. Waste with surface dose rates above 200 millirem/hour (0.002 sievert/hour) and waste that has been managed remotely (remote-handled). In 1992, Congress passed the WIPP Land Withdrawal Act, which created the regulatory framework under which DOE was to operate the facility, and authorized disposal of waste up to 1,000 rems/hour (10 Sievert/hour). Subsequently, DOE submitted applications to the Environmental Protection Agency (EPA), at the Federal level, for certification to operate WIPP, and to the New Mexico Environment Department (NMED), at the State level, for a hazardous waste permit. Both applications described the characterization methods that DOE proposed to use to ensure only compliant waste was shipped to WIPP. No distinction was employed in these methods concerning the surface dose rate from the waste. During the applications review, both regulatory agencies came to the conclusion in their approval that DOE had not demonstrated that remote-handled transuranic (RH-TRU) waste could be adequately characterized. Therefore, WIPP was only granted approval to begin waste disposal operations of waste with surface dose rates less than 200 millirem/hour (0.002 sievert/hour) — or contact-handled transuranic (CH-TRU) waste. Emplacement of CH-TRU waste in WIPP began March 26, 1999. However, WIPP was designed for disposal of both CH- and RH-TRU waste, with the RH-TRU waste in canisters emplaced in the walls of the underground disposal rooms and CH-TRU waste in containers in the associated open drifts. Therefore, as disposal rooms filled with CH-TRU waste, the space along the walls for RH-TRU waste disposal was lost. This made removal of the regulatory prohibition on RH-TRU waste a very high priority, and DOE immediately began an iterative process to change the two regulatory bases for RH-TRU waste disposal. These changes focused on how DOE could rely on CH-TRU characterization methods for adequate characterization of RH-TRU waste. On January 23, 2007, the first shipment of RH-TRU waste was finally received at WIPP. The revised EPA certification and NMED permit now both consider all waste characterization methods to be equally effective when applied to either CH- or RH-TRU waste, as DOE maintained in the original applications over 10 years ago.

Copyright © 2007 by ASME



Interactive Graphics


Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In