0

Full Content is available to subscribers

Subscribe/Learn More  >

Capacity Mapping for Optimum Utilization of Pulverizers for Coal Fired Boilers

[+] Author Affiliations
Chittatosh Bhattacharya

National Power Training Institute, Durgapur, West Bengal, India

Paper No. POWER2006-88005, pp. 137-145; 9 pages
doi:10.1115/POWER2006-88005
From:
  • ASME 2006 Power Conference
  • ASME 2006 Power Conference
  • Atlanta, Georgia, USA, May 2–4, 2006
  • Conference Sponsors: Power Division
  • ISBN: 0-7918-4205-3 | eISBN: 0-7918-3776-9
  • Copyright © 2006 by ASME

abstract

The pulverizer plays a pivotal role in coal based thermal power generation. The improper coal fineness or drying reflects a quality-wise deterioration. This results in flame instability, unburnt combustible loss, and a propensity to slagging or clinker formation. Simultaneously, an improper air-coal ratio may result in either the coal pipe choke or the flame impingement, an unbalanced heat release, an excessive FEGT, overheating of the tube metal, etc, resulting on the reduced output and excessive pulverizer rejects. In general, the base capacity of the pulverizer is a function of coal and air quality, conditions of grinding elements, classifier and other internals. The capacity mapping is a process of comparison of standard inputs with actual fired inputs to assess the available standard output capacity of the pulverizer. In fact, this will provide a standard guideline over operational adjustment and maintenance requirement of the pulverizer. The base capacity is a function of grindability; fineness requirement may vary depending upon the volatile matter content of the coal and the input coal size. The quantity and inlet temperature of primary air limits the drying capacity. The base airflow requirement will change depending upon the quality of raw coal and output requirement. It should be sufficient to dry pulverized coal. Drying capacity is also limited by utmost P.A. fan power to supply air. The P.A. temperature is limited by APH inlet flue gas temperature — an increase of this will result in efficiency loss of the boiler. Besides, the higher P.A. inlet temperature can be attained through economizer gas by-pass, the SCAPH, partial flue gas recirculation. The primary air/coal ratio, a variable quantity within the pulverizer operating range, increases with decrease in grindability or pulverizer output and decreases with decrease in volatile matter. Again, the flammability of mixture has to be monitored on explosion limit. Through calibration, the P.A. flow and efficiency of conveyance can be verified. The velocities of coal/air mixture to prevent fallout or to avoid erosion in the coal carrier pipe are dependent on the pulverized coal particle size distribution. Metal loss of grinding elements inversely depends on the YGP index of coal. Besides, variations of dynamic load on grinding elements, wearing of pulverizer internal components affect the available pulverizing capacity and percentage rejects. Therefore, the capacity mapping is necessary to ensure the available pulverizer capacity to avoid overcapacity or under capacity running of pulverizing system, optimizing auxiliary power consumption, This will provide a guideline on the distribution of raw coal feeding in different pulverizers of a boiler to maximize operating system efficiency and control resulting a more cost effective heat rate.

Copyright © 2006 by ASME
Topics: Boilers , Coal

Figures

Tables

Interactive Graphics

Video

Country-Specific Mortality and Growth Failure in Infancy and Yound Children and Association With Material Stature

Use interactive graphics and maps to view and sort country-specific infant and early dhildhood mortality and growth failure data and their association with maternal

NOTE:
Citing articles are presented as examples only. In non-demo SCM6 implementation, integration with CrossRef’s "Cited By" API will populate this tab (http://www.crossref.org/citedby.html).

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In